Follow Us on Facebook

Get updates from AllFreeSewing.com posted directly to your News Feed.

Thanks for signing up!

(1)

DIY Bath Mat With Pockets

By: Maureen Wilson from Made By Marzipan

Rate This Article

Comment On This Article

Kneeling on the hard title floor while giving the kids a bath can do a number on your knees. Create the DIY Bath Mat with Pockets. This free sewing project will not only give knees a comfy place to rest, it's easy storage for bath supplies. Watch Maureen Wilson as she leads you through step to creating this handy tub side mat.

DIY Bath Mat With Pockets

Materials:

  • Plastic shower curtain
  • Velcro, 6 in.
  • Foam cushion, 1x15x17
  • Suction cups, 3
  • Ribbon, 18 in.
  • Wire (optional)
  • Sewing machine & thread


Supply Tips:

  • You’ll need a plastic shower curtain. This one was $10 at Wal-Mart, but there were cheaper ones available as well.
     
  • You’ll also need a foam cushion. If your shower curtain is transparent, be sure to select a white cushion. This piece of foam is 1x15x17 inches, and cost $5 at JoAnn’s. Make sure the foam you use is wide enough for you to kneel on comfortably, and not taller than the side of your tub.
     
  • You’ll need 3 suction cups, either medium or large sized. You can find these in the craft section, they’re sold next to the plastic suncatchers. This package was $2 at Wal-Mart.


Instructions:
Begin by measuring the side and rim of your tub. Next we’ll cut two large rectangles that will become the front and back of the Tubside Mat. Here’s the formula for figuring out how long to make these pieces. On the right side, I’ve included the measurements for my tub and cushion.

LENGTH

Height of tub + 15.0

Width of rim of tub + 3.5

Length of cushion + 15.0

Thickness of cushion + 1.0

6 in. (seams & overhang) + 6.0

_____

40.5

Here’s the formula for figuring out how wide to make these pieces:

WIDTH

Thickness of cushion x 2 + 2.0

Width of cushion 17.0

_____

19.0
 

  1. We’re also going to cut a pocket piece. It will need to be the same width as the other two pieces, plus another 3 inches so it will have some give. The height should be 15 inches.
     
  2. Fold the pocket piece in half so that it is now 7.5 inches tall. Right sides should be together. Pin the long bottom edge. Sew with a 1/2 inch seam, then turn right side out. Insert your hand into the tube and poke out the seams.
     
  3. Topstitch the long folded edge of the pocket piece.
     
  4. Now we’ll add the pocket piece to the main rectangle. Measure from the bottom edge of the mat, so you’ll know where to place the bottom of the pocket. Add the thickness of your cushion x2, plus the length of your cushion, and pin the pocket there. It should be on the right side of the mat, and the topstitched edge will become the top of the pocket.
     
  5. Pin the short sides of the pocket first, aligning with the edges of the mat. The pocket piece is wider than the mat, so that the pockets will hold more. You’ll need to make a series of tiny folds, or pleats, as you pin the bottom edge of the pocket to the mat. Make the pocket fit the mat in this manner.
     
  6. Sew the pocket to the mat along the bottom edge of the pocket.
     
  7. Next we’ll divide the pocket panel by adding two rows of stitches side-by-side down the center. Having two rows will make the pocket more durable.
     
  8. You could add your rough Velcro strips in the bottom corners right now, about 2 inches in from the edges. I added mine a little later, but it probably would have been easier to do it now… it’s up to you.
     
  9. Layer the back mat piece on top of your front mat piece, right sides together, and pin. Sew the long sides and bottom with a 1/2 inch seam, leaving the top edge open.
     
  10. Clip the two corners, being careful not to cut your stitches. Turn right side out and poke out the seams. This is when I added my Velcro to the bottom corners. If you’re adding it now, be careful that you are sewing through only the top layer of the mat!
     
  11. Now slide the cushion into the mat. Be sure to push it all the way to the bottom. Sew alongside the top edge of the cushion to secure.
     
  12. It’s time to add the coordinating pieces of Velcro. To get the proper placement, fold the cushion up on top of the mat. Note where the Velcro touches, and pin the matching Velcro tabs there. Sew in place. I only sewed through the top layer, but realized later that it didn’t matter whether I sewed through both. Either way is fine.
     
  13. Finally, we’ll add the ribbon loops for the suction cups. Fold the top open edge of the mat inward a 1/2 inch. Add one ribbon loop to each corner, and one to the center. Pin the edge shut, and sew. Add two rows of stitches for durability: one at 1/4 inch, and another at 1/8 inch.
     
  14. Add one suction cup to each loop. Depending on the type of hook your suction cups have, you may want to remove the hook provided and instead wrap a piece of wire around the ribbon and cup so it won’t slide off.

 

 

 

Newsletter Signup

Free Newsletter!

Subscribe to our Sewing It Up! newsletter for free sewing patterns and projects, technique tutorials and videos, special offers, and sew much more!

Please Wait

Thanks for signing up

Sorry, we could not sign you up.

Something worth saving?

Register now for FREE to:

  • SAVE all your favorite patterns
  • ADD personal notes
  • QUICKLY reference your patterns

 

Connect with Us

Find us online

Facebook Google Plus Twitter Pinterest Twitter Blog Email RSS

© Copyright 2013 Prime Publishing, LLC. All rights reserved.

www.allfreesewing.com